Additional information
| Manufacturer | Torch |
|---|
Back to 2019-2020 Ford Ranger Lift Kits
Torch 3-Inch Lift Kit For 2019-2023 Ford Ranger
TORCH 3″ Adjustable Front Leveling Lift Kit
Enhance the look of your vehicle and run larger tires with TORCH Off Road’s Lift Kit
- Our TORCH Off Road strut spacers are an easy way to get up to 3″ of lift on the new 2019+ Ranger models.
- Installs right on top of your strut so you won’t need longer shocks.
- Built tough to handle any terrain that you’re driving on.
- Includes a 1/2″ lift stackable plate so you’re able to choose 3 different levels of lift.
About The Product
Kit Includes:
- 2.5″ Front Lift Strut Spacers with Hardware0.5″ Front Lift Strut Spacer Plate (stackable)
- Combine to make 3″ Front Lift or use separately for either 2.5″ or 0.5″ of lift
- Comes with instructions and everything shown in the picture.
Benefits:
- Easy 1-2 hour Installation Process***
- Increase Ground Clearance And Install Larger Custom Rims & Tires
Technical Notes
- Front Lift: 2.5″-3″
- Front Strut Spacers will generate 2.5″ of Lift, it is NOT a 2.5″ thick spacer.
- An alignment is always recommended after altering the height of your vehicle.***
Related products
Fabtech 3-1/2″ Lift W/Dirt Logic Shocks Ford 2019-2023
This quality 2019 Ford Ranger Upper Control Arm system is perfect for owners looking to increase ride height to run slightly larger tires than factory. The system will provide additional wheel travel with no suspension bind at full droop.
Lift is accomplished with steel spacers that utilize the factory Coilover shocks for a stock like ride.
Fabtech’s Upper Control Arms address the geometry of the front suspension with the new ride height for proper align ability. Heavy duty ball joints allow for extended suspension travel to eliminate binding. The system has been designed for proper CV axle angle and plunge thus eliminating the need to reposition the front differential.
Included in this system is Fabtech’s Offset Intrusion Beam Kit that allows use of 33" tires. The factory Intrusion Beams are located in the front fenderwells, forward and back of the tire. They limit the size of the tire you can install while being an integral part of the front collision safety impact feature of the vehicle. Rather than modifying or removing the Beams for tire clearance, Fabtech provides replacement Offset Intrusion Beams. They are constructed of 1/4" thick steel and are a welded box design for maximum strength. They allow full steer with 33/1250R tires w/ a 5" back space wheel.
Rear lift comes from 1.5" blocks and u-bolts.
Features
- Value priced system with Fabtech quality
- Increased ground clearance for offroad
- Tubular UCA design with urethane bushings for quiet ride
- Extended range upper ball joints allow for increased travel
- Offset Intrusion Beams for full steer tire clearance
- Easy bolt on installation
Rough Country 2.5-Inch Leveling Kit For 2019-2020 Ford Ranger
Give your Ford Ranger an improved, aggressive look with Rough Country’s 2.5in Leveling kit! This easy-to-install kit levels your vehicle from front to rear giving you increased ground clearance to run larger tires while eliminating the nose-down factory look for a commanding presence that can’t be ignored.
When it comes to leveling your Ranger, a small lift can make a huge difference! By lifting the front end of the vehicle to match the height of the rear, you get an instant transformation in looks and ground clearance that’s sure to turn heads wherever you go.
Each kit features a set of front strut spacers, laser cut for a precise fit and powder coated black to resist the elements. Rough Country’s 2.5in Leveling Kit features an easy, 100% bolt-on installation process with no need for complicated strut disassembly. Includes a Lifetime Replacement Guarantee!
Features
- Levels the front with the rear of the vehicle
- Easy bolt-on installation
- Maintains factory ride quality
- Increased ground clearance
- No need to disassemble your struts to install
Notes - Important
- After-market wheels must have a minimum of 93.1mm center bore, and maximum 6.5” back spacing.
- Wheels with less than 6.5” backspacing may require slight trimming.
- 9” wide wheels will require trimming.
BDS 2.5-Inch Lift Kit For 2019-2023 Ford Ranger
Overview
Properly level the front of your 2019-2023 Ford Ranger truck by installing this 2.5-inch leveling kit from BDS. Specially designed for the new Ranger, this 2.5" leveling kit is engineered for additional tire clearance and improved performance without overextending the suspension or driveline angles at full suspension droop. To prevent maxing out ball joints or CV damage, BDS gets around this issue by using a 2-piece design with a smaller top mounted steel strut spacer in combination with a preload spacer. To further ensure proper drivetrain geometry the front differential is repositioned using relocation brackets. These brackets correct CV axle angle while allowing the use of the factory front skid plates. The lift kit includes steel top mount strut spacers, pre-load spacers, differential relocation brackets and custom-tuned NX2 Nitro or FOX Performance series shocks. Give your new Ranger the extra boost with this 2.5" leveling kit from BDS Suspension.Features & Benefits
- Easy, 100% Bolt-on installation
- Maintains factory like ride quality
- Standard NX2 Nitro shocks with vehicle-specific valving for better control
- Upgrade to FOX 2.0 Performance Series shocks for maximum performance on and off-road
Recommended Tires & Wheels
(Trimming may be required)- 285 / 70 with 17 x 8 and in. Backspace
- 285 / 65 with 18 x 9 and in. Backspace
Rear Shock Option
NX2 Nitro Series- Nitrogen-charged
- Twin-tube design
- 10-stage velocity-sensitive valving
- Dual-welded ends for increased strength
- 1-3/8-inch high-flow piston
- Self-lubricating seals
- Silver powder coat finish
- 2-inch Impact extruded aluminum body
- Internal floating piston (IFP) monotube design
- CNC machined 6061-T6 aluminum mounting ends
- Massive 5/8-inch hard chrome plated heat-treated alloy steel shaft
- Race-developed high-flow piston design
- Application-specific valving to maximize performance
- Long-lasting clear anodized finish
BDS 2-Inch Leveling Kit For 2019-2023 Ford Ranger
Overview
Level the front of your 2019-2023 Ford Ranger truck by installing this 2-inch leveling kit from BDS. Specially designed for the new Ranger, this 2" leveling kit is engineered for additional tire clearance and improved performance without overextending the suspension or driveline angles at full suspension droop. To prevent maxing out ball joints or CV damage, BDS gets around this issue by using a 2-piece design with a smaller top mounted steel strut spacer in combination with a preload spacer. The lift kit includes steel top mount strut spacers, pre-load spacer and custom-tuned NX2 Nitro or FOX Performance series shocks. Give your new Ranger the extra boost with this 2" leveling kit from BDS Suspension.Features & Benefits
- Easy, 100% Bolt-on installation
- Maintains factory like ride quality
- Standard NX2 Nitro shocks with vehicle-specific valving for better control
- Upgrade to FOX 2.0 Performance Series shocks for maximum performance on and off-road
Recommended Tires & Wheels
(Trimming may be required) 285 / 70 with 17 x 8 and in. Backspace 285 / 65 with 18 x 9 and in. BackspaceRear Shock Option
NX2 Nitro Series- Nitrogen-charged
- Twin-tube design
- 10-stage velocity-sensitive valving
- Dual-welded ends for increased strength
- 1-3/8-inch high-flow piston
- Self-lubricating seals
- Silver powder coat finish
- 2-inch Impact extruded aluminum body
- Internal floating piston (IFP) monotube design
- CNC machined 6061-T6 aluminum mounting ends
- Massive 5/8-inch hard chrome plated heat-treated alloy steel shaft
- Race-developed high-flow piston design
- Application-specific valving to maximize performance
- Long-lasting clear anodized finish